r09ds0038ej0100 rev.1.00 p age 1 of 9 apr 16, 2012 ne3516s02 data s heet n - c hannel gaas hj - fet, x to ku b and l ow n oise and h igh - g ain features ? low noise figure and high associated gain nf = 0.35 db typ., g a = 14 db typ. @ f = 12 ghz, v ds = 2 v, i d = 10 ma nf = 0.35 db typ., g a = 13.5 db typ. @ f = 12 ghz, v ds = 2 v, i d = 6 ma (reference value) ? 4 - pin micro - x plastic (s02) package applications ? x to ku band dbs lnb ? other ku band communication system ordering information part number order number package quant ity marking supplying form ne351 6 s02 - t1c ne351 6 s02 - t1c - a s02 package (pb - free) 2 kpcs/reel p ? 8 mm wide embossed taping ? pin 4 (gate) faces the perforation side of the tape ne351 6 s02 - t1d ne351 6 s02 - t1d - a 10 kpcs/reel remark to order evaluation sa mples, please contact your nearby sales office. part nu mber for sample order: ne351 6s02 - a absolute maximum ratings (t a = +25 ? parameter symbol ratings unit drain to source voltage v ds 4.0 v gate to source voltage v gs C 3.0 v drain current i d i ds s ma gate current i g 100 ? a total power dissipation note p tot 165 mw channel temperature t ch + 125 ? c storage temperature t stg C 65 to +125 ? c note: mounted on 1.08 cm 2 ? 1.0 mm (t) glass epoxy pwb recommended operating range ( t a = +25 ? parameter symbol min. typ. max. unit drain to source voltage v ds + 1 + 2 + 3 v drain current i d 5 10 15 ma input power p in C C 0 dbm caution observe precautions when handling because these devices are sensitive to electrostatic discharge . r09ds0038ej0100 rev.1.00 apr 16, 2012 rev.1.00 apr 16, 2012
ne3516s02 r09ds0038ej0100 rev.1.00 p age 2 of 9 apr 16, 2012 electrical characteristics ( t a = +25 ? parameter symbol test conditions min. typ. max. unit gate to source leak current i gso v gs = ? 3.0 v ? 0.5 10 ? a saturated drain current i dss v ds = 2 v, v gs = 0 v 15 30 60 ma gate to source cut - off voltage v gs(off) v ds = 2v, i d = 100 ? a ? 0.2 ? 0.5 ? 1.3 v transconductance gm v ds = 2 v, i d = 10 ma 55 65 ? ms noise figure nf v ds = 2 v, i d = 10 ma, f = 12 ghz ? 0. 35 0.50 db associated gain g a 13 14 ? db standard characteristics for reference (t a = +25 ? parameter symbol test conditions reference value unit noise figure nf v ds = 2 v, i d = 6 ma, f = 12 ghz 0.35 db associated gain g a 13.5 db
ne3516s02 r09ds0038ej0100 rev.1.00 p age 3 of 9 apr 16, 2012 typical characteristics (t a = +25 ? remark the graph indicates nominal characteristics .
ne3516s02 r09ds0038ej0100 rev.1.00 p age 4 of 9 apr 16, 2012 s - parameters
ne3516s02 r09ds0038ej0100 rev.1.00 p age 5 of 9 apr 16, 2012 rf measuring layout pattern (reference only) (unit: mm)
ne3516s02 r09ds0038ej0100 rev.1.00 p age 7 of 9 apr 16, 2012 package dimens ions s02 (unit: mm)
ne3516s02 r09ds0038ej0100 rev.1.00 p age 8 of 9 apr 16, 2012 recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales o ffice. soldering method soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 ? c or below time at peak temperature : 10 seconds or less time at temperature of 220 ? c or higher : 60 seconds or less preheat ing time at 120 to 180 ? c : 120 ? 30 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2% (wt.) or below ir260 partial heating peak temperature (terminal temperature) : 350 ? c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin flux (% mass) : 0.2% (wt.) or below hs350 caution do not use different soldering methods together (ex cep t for partial heating) .
ne3516s02 r09ds0038ej0100 rev.1.00 p age 9 of 9 apr 16, 2012 caution gaas products this product uses gallium arse nide (gaas). gaas vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposing of the product. if there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. exclude the product from general industrial was te and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the product. ? do not lick the product or in any way al low it to enter the mouth.
all trademarks and registered trademarks are the property of their respective owners. c - 1 revision history ne 3516s02 data sheet rev. date description page summary 1.0 0 apr 16 , 201 2 C first edition issued
|
